How To Replace A Bathtub (For Newbies).
How To Replace A Bathtub (For Newbies).
Blog Article
Do you find yourself in search of know-how concerning Tools You Need to Install a New Bathtub ?
Setting up a bathtub isn't specifically rocket science, however it does call for solid plumbing, woodworking, and sometimes, tiling abilities. Replacing an old tub with a brand-new one is additionally a moderately difficult job. If the old tub is easily available, the job can move immediately; if you have to open a wall surface to get rid of the old tub and also position the brand-new bathtub, the job is a lot harder. In either situation, the task is within a home handyman's abilities, although you will need an assistant to move out the old tub as well as embeded in the brand-new one. See to it you have certified yourself for the task and are comfortable trying it. Rather than working with a contractor to take over a halfway-completed task, it is better to think about using one before you begin. Chances are you might need a specialist plumber to make tube connections.
This short article will certainly assist you mount a brand-new bathtub in your restroom if you have actually already purchased a new tub as well as do not require to change the plan of your previous water pipelines.
Your tools as well as product checklist ought to consist of the following:
Removing Old Taps
If you need to change old faucets with brand-new ones as a part of your installation, then the first thing you ought to do is detach the supply of water. After doing so, switch on the faucets to drain any water remaining in the system. The procedure of getting rid of the existing faucets can be rather problematic due to the restricted accessibility that is commonly the instance.
Use a basin wrench (crowsfoot spanner) or a tap tool to reverse the nut that attaches the supply pipes to the taps. Have a cloth ready for the continuing to be water that will certainly originate from the pipes. When the supply pipes have actually been eliminated, make use of the exact same device to loosen the nut that holds the taps onto the bath/basin. You will certainly need to quit the solitary taps from transforming during this procedure. When the faucets have been gotten rid of, the holes in the bath/basin will certainly need to be cleansed of any old securing substance.
Before proceeding to fit the new taps, compare the pipe links on the old taps to the new taps. If the old taps are longer than the brand-new taps, then a shank adapter is needed for the brand-new faucets to fit.
Suitable New Touches
If the tails of the new taps are plastic, after that you will certainly need a plastic connector to prevent damages to the string. One end of the connector fits on the plastic tail of the faucet and also the various other end supplies a connection to the existing supply pipes.
If you need to fit a monobloc, then you will require reducing couplers, which links the 10mm pipe of the monobloc to the basic 15mm supply pipe.
Next off, place the faucet in the installing opening in the bath/basin making sure that the washing machines remain in location between the tap and also the sink. Protect the tap in place with the supplier supplied backnut. Once the tap is firmly in place, the supply pipes can be attached to the tails of the taps. The faucets can either be attached by utilizing corrugated copper piping or with typical tap adapters. The previous type should be attached to the faucet finishes first, tightening up just by hand. The supply pipes can later be linked to the various other end. Tighten both ends with a spanner after both ends have actually been linked.
Installing the Bathtub
Utilizing the two wood boards under its feet, position the bathtub in the called for position. The wooden boards are handy in uniformly spreading the weight of the tub over the area of the boards as opposed to focusing all the weight onto 4 little factors.
The next objective is to guarantee that the tub is leveled all round. This can be attained by checking the level and readjusting the feet on the bathtub till the level checks out degree.
To set up faucets, fit all-time low of the furthest adaptable faucet connector to the appropriate supply pipe by making a compression join; after that do the exact same for the other tap.
Activate the water supply as well as inspect all joints as well as brand-new pipework for leaks and also tighten them if necessary. Fill up the bathtub and additionally check the overflow outlet and the typical outlet for leakages.
Finally, take care of the bath paneling as explained in the supplier's instruction manual. Tiling as well as sealing around the bathtub must wait until the tub has been utilized at the very least once as this will resolve it into its final placement.
Planning for the Installment
Firstly, the supporting structure supplied with the bath must be fitted (if needed) according to the manufacturer's directions. Next off, fit the taps or mixer to the bathtub. When suitable the tap block, it is essential to ensure that if the faucet comes with a plastic washer, it is fitted in between the bathroom as well as the faucets. On a plastic bath, it is also practical to fit a sustaining plate under the taps system to avoid pressure on the bath tub.
Fit the flexible tap ports to the bottom of both faucets making use of 2 nuts and olives (occasionally provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and after that pass the electrical outlet via the hole in the bathroom. Make use of the nut supplied by the manufacturer to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the adaptable overflow pipe to the overflow outlet. After that, screw the pipeline to the overflow face which must be fitted inside the bathroom. Ensure you use all of the supplied washing machines.
Attach the trap to the bottom of the waste outlet on the bath tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and also screw on the catch to the electrical outlet. Link the bottom of the overflow tube in a similar manner.The bathroom need to now be ready to be fitted in its final position.
Tiling Around the Bathtub
In the location where the bathroom satisfies the floor tile, it is required to seal the joins with a silicone rubber caulking. This is necessary as the installation can move sufficient to break a stiff seal, triggering the water to permeate the wall between the bath and also the tiling, causing difficulties with wetness and possible leaks to the ceiling listed below.
You can select from a range of coloured sealants to assimilate your components and installations. They are marketed in tubes and also cartridges, and also are capable of securing voids as much as a width of 3mm (1/8 inch). If you have a larger void to fill up, you can load it with twists of drenched paper or soft rope. Remember to always load the tub with water before sealing, to permit the motion experienced when the tub remains in usage. The sealant can crack rather very early if you do not take into consideration this activity prior to sealing.
Conversely, ceramic coving or quadrant ceramic tiles can be used to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to dimension, are also easily readily available on the marketplace. It is recommended to fit the tiles using water-resistant or waterproof adhesive and also grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
Do you like reading about Installing A Bathtub? Place a remark further down. We will be delighted to find out your thinking about this blog. We hope to see you back again soon. Enjoyed our post? Please share it. Help somebody else find it. Thanks a bunch for your time. Kindly check up our blog back soon.
Schedule Service Now Report this page